Showing posts with label recalls. Show all posts
Showing posts with label recalls. Show all posts

Tuesday, November 4, 2014

Ask Joe Mechanic: Current Recalls


We will return to our regular content next week.  This week will again feature the most current recalls that are listed on www.nhtsa.gov.  If after reviewing the recalls below, you discover that you own an affected vehicle, please contact your local dealer at your earliest convenience.  Your dealer will be able to tell you how to proceed with your automobile. 

This Week’s (11/4/14) Recalls:
Nissan North America, Inc. (Nissan) is recalling certain model year 2014 Infiniti Q50 hybrid vehicles manufactured December 10, 2012, to June 25, 2014, and Infiniti Q70 hybrid vehicles manufactured November 7, 2013, to May 7, 2014. Due to a software error, the electric motor may stop working while the vehicle is being driven using the electric motor only.  The stall-like condition that occurs when the electric motor stops working may increase the risk of a crash.

Nissan North America, Inc. (Nissan) is recalling certain model year 2014 Infiniti Q50 hybrid vehicles manufactured October 16, 2013, to January 27, 2014, and Infiniti Q70 hybrid vehicles manufactured November 7, 2013, to December 10, 2013. The affected vehicles may have been assembled with transmissions whose housings were damaged during their manufacturing.  The damaged housings could crack and fracture, creating road debris and disabling the vehicle, increasing the risk of a crash.

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2014 Toyota Avalon, Camry, Sienna, and Highlander and model year 2015 Lexus RX350 vehicles. Fuel may leak from the one of the fuel delivery pipes in the engine compartment.  A fuel leak in the presence of an ignition source increases the risk of a fire.

Chrysler Group LLC (Chrysler) is recalling certain model year 2014 Ram ProMaster vehicles manufactured April 23, 2013, to August 22, 2014. In the affected vehicles, the Tire Pressure Monitoring System (TPMS) may fail to learn the locations of the individual sensors while the vehicle is being driven. As a result, the low tire pressure warning light will illuminate, despite the the tire pressures being within specification. Should one of the tires lose air pressure, the driver would not be notified of the change in air pressure. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 138, "Tire Pressure Monitoring Systems."  If the TPMS light illuminates because the sensors cannot be located, it could mask an actual low tire pressure condition, possibly resulting in tire failure, increasing the risk of a crash.

Chrysler Group LLC (Chrysler) is recalling certain model year 2010-2014 Ram 2500, 3500, 4500, and 5500 trucks manufactured March 27, 2009, to September 5, 2013. In the affected vehicles, the electrical connectors of the diesel fuel heater may overheat.  If the connectors overheat, the fuel heater may leak fuel, increasing the risk of a fire

Chrysler Group LLC (Chrysler) is recalling certain model year 2014 Dodge Durango, and Jeep Grand Cherokee vehicles manufactured October 3, 2013, to April 11, 2014. Due to an issue with the software for the Steering Column Control Module (SCCM), the Electronic Stability Control (ESC) may be disabled.  If the ESC is disabled during certain driving situations, the driver may not be able to adequately control the vehicle, increasing the risk of a crash.

Chrysler Group LLC (Chrysler) is recalling certain model year 2014 Dodge Durango vehicles manufactured June 2, 2013, to June 28, 2014, and 2014 Jeep Grand Cherokee vehicles manufactured October 30, 2012, to April 30, 2014. Due to a fault within the Occupant Restraint Control (OCR) module, the frontal air bags, seat belt pretensioners, and side air bags may be disabled. The malfunction indicator light “MIL” should illuminate to initially warn drivers of a failure.  If the frontal air bags, seat belt pretensioners, and side air bags are disabled, there is an increased risk of injury to the vehicle occupants in the event of a vehicle crash that necessitates use of the passive restraint system.

Mitsubishi Motors North America, Inc. (Mitsubishi) is recalling certain model year 2007-2009 Outlander vehicles manufactured December 15, 2006, to October 31, 2007, and April 16, 2008, to August 22, 2009. In the affected vehicles, the brake light switch may malfunction causing the brake lights to not illuminate during brake application.  Brake lights that are inoperative would not warn other drivers that the vehicle is stopping, increasing the risk of a crash.

Monday, November 3, 2014

Ask Joe Mechanic: The Importance of Recalls


This week, I am departing from my regularly planned article. The reason for this departure is due to the second major vehicle recall this year and one that could possibly be the greatest recall in the history of the auto industry.  I am speaking of the airbag recall.  Unfortunately, this recall could potentially affect over 30 million vehicles.



How can you know if your vehicle is involved in this or any other recall?  Well, every week I try to include in this column, whatever new recalls have been posted in the previous week.  This is something that I take very seriously and have since day one of writing the Ask Joe Mechanic column.  I like to keep our readers informed of all auto-related subjects.



Or, it is quite simple to find out online if any of the vehicles that you own have outstanding recalls posted against them.  No matter how old the recall may be, as long as it is still considered open – meaning the manufacturer is obligated to make a repair if you bring the vehicle to the dealer.  Generally, that means any safety recall posted in the past fifteen years. All you have to do is go to the National Highway Traffic Safety Administration website, www.nhtsa.gov and you enter the VIN number of your vehicle.  After doing so, the site lets you know if there is anything that you need to have taken care of with your particular vehicle.   



Please, for your safety and the safety of other drivers, visit this website and check on each and every vehicle that you own.

Wednesday, March 26, 2014

Ask Joe Mechanic - CNG/LNG/LPG Vehicles


            Compressed natural gas and Propane gas are two technologies that have been well tested and with the reduction of cost of natural gas, seems to be a great alternative fuel source. A natural gas vehicle is an alternative fuel vehicle that uses compressed natural gas (CNG) or liquefied natural gas (LNG) as a cleaner alternative to other fossil fuels. Natural gas vehicles should not be confused with vehicles powered by propane (LPG), which is a fuel with a fundamentally different composition.


            As of 2009, the U.S. had a fleet of 114,270 compressed natural gas (CNG) vehicles, mostly buses; 147,030 vehicles running on liquefied petroleum gas (LPG); and 3,176 vehicles liquefied natural gas (LNG). Worldwide, there were 14.8 million natural gas vehicles by 2011.



            Existing gasoline-powered vehicles may be converted to run on CNG or LNG, and can be dedicated (running only on natural gas) or bi-fuel (running on either gasoline or natural gas. Diesel engines for heavy trucks and busses can also be converted and can be dedicated with the addition of new heads containing spark ignition systems, or can be run on a blend of diesel and natural gas, with the primary fuel being natural gas and a small amount of diesel fuel being used as an ignition source. An increasing number of vehicles worldwide are being manufactured to run on CNG. Until recently, the Honda Civic GX was the only NGV commercially available in the US market., however now Ford, GM and Ram have bi-fuel offerings in their vehicle lineup. Fords approach is to offer a bi-fuel prep kit as a factory option, and then have the customer choose an authorized partner to install the natural gas equipment.



Choosing GM's bi-fuel option sends the HD pickups with the 6.0L gasoline engine to IMPCO in Indiana to upfit the vehicle to run on CNG. Ram currently is the only pickup truck manufacturer with a truly factory-installed bi-fuel system available in the U.S. market. Outside the U.S. GM do Brazil introduced the MultiPower engine in August 2004 which was capable of using CNG, alcohol and gasoline (E20-E25 blend) as fuel, and it was used in the Chevrolet Astra 2.0 model 2005, aimed at the taxi market. In 2006 the Brazilian subsidiary of FIAT introduced the Fiat Siena Tetra fuel, a four-fuel car developed under Magneti Marelli of Fiat Brazil. This automobile can run on natural gas (CNG); 100 percent ethanol (E100); E20 to E25 gasoline blend, Brazil's mandatory gasoline; and pure gasoline, though no longer available in Brazil it is used in neighboring countries.



             NGV filling stations can be located anywhere that natural gas lines exist. Compressors (CNG) or liquifaction plants (LNG) are usually built on large scale but with CNG small home refueling stations are possible. A company called FuelMaker pioneered such a system called Phill Home Refueling Appliance (known as "Phill"), which they developed in partnership with Honda for the American GX model. Phill is now manufactured and sold by BRC FuelMaker, a division of Fuel Systems Solutions, Inc.

           

 CNG may also be mixed with biogas, produced from landfills or wastewater, which doesn't increase the concentration of carbon in the atmosphere.



            Despite its advantages, the use of natural gas vehicles faces several limitations, including fuel storage and infrastructure available for delivery and distribution at fueling stations. CNG must be stored in high-pressure cylinders (3000psi to 3600psi operation pressure), and LNG must be stored in cryogenic cylinders (-260F to -200F). These cylinders take up more space than gasoline or diesel tanks that can be molded in intricate shapes to store more fuel and use less on-vehicle space. CNG tanks are usually located in the vehicle's trunk or pickup bed, reducing the space available for other cargo. This problem can be solved by installing the tanks under the body of the vehicle, or on the roof (typical for busses), leaving cargo areas free. As with other alternative fuels, other barriers for widespread use of NGVs are natural gas distribution to and at fueling stations as well as the low number of CNG and LNG stations.



             Though LNG and CNG are both considered NGVs, the technologies are vastly different. Refueling equipment, fuel cost, pumps, tanks, hazards, capital costs are all different. One thing they share is that due to engines made for gasoline, computer controlled valves to control fuel mixtures are required for both of them, often being proprietary and specific to the manufacturer. The on-engine technology for fuel metering is the same for LNG and CNG.



            CNG, or compressed natural gas, is stored at high pressure, 3,000 to 3,600 pounds per square inch (21 to 25 MPa). The required tank is more massive and costly than a conventional fuel tank. Refueling stations are more expensive to operate than LNG stations because of the energy required for compression. Time to fill a CNG tank varies greatly depending on the station. Home refuelers typically fill at about 0.4 GGE/hr. "Fast-fill" stations may be able to refill a 10 GGE tank in 5–10 minutes. Also, because of the lower energy density, the range on CNG is limited by comparison to LNG.



            LNG, or liquified natural gas, is natural gas that has been cooled to a point that it is a cryogenic liquid. In its liquid state, it is still more than 2 times as dense as CNG. LNG is dispensed from bulk storage tanks at LNG fuel stations at rates exceeding 20 GGE/min. Because of its cryogenic nature, it is stored in specially designed insulated tanks. Generally speaking, these tanks operate at fairly low pressures (about 70-150 psi) when compared to CNG. A vaporizer is mounted in the fuel system that turns the LNG into a gas (which may simply be considered low pressure CNG).



            LNG – and especially CNG – tends to corrode and wear the parts of an engine less rapidly than gasoline. Thus it's quite common to find diesel engine NGVs with high mileages (over 500,000 miles). Emissions are cleaner, with lower emissions of carbon and lower particulate emissions per equivalent distance traveled. There is generally less wasted fuel. CNG-powered vehicles are considered to be safer than gasoline-powered vehicles.



            Autogas, also known as LPG, has different chemical composition, but still petroleum based gas, has a number of inherent advantages and disadvantages, as well as noninherent ones. The inherent advantage of autogas over CNG is that it requires far less compression (20% of CNG cost), is denser as its a liquid at room temperature, and thus far cheaper tanks (consumer) and fuel compressors (provider) than CNG. As compared to LNG, it requires no chilling (and thus less energy), or problems associated with extreme cold such as frostbite. Like NGV, it also has advantages over gasoline and diesel in cleaner emissions, along with less wear on engines over gasoline. The major drawback of LPG is its safety, the fuel is heavier than air, which causes it to collect in a low spot in the event of a leak, making it far more hazardous to use, as more care is needed.



            Varieties of LPG bought and sold include mixes that are primarily propane (C3H8), primarily butane (C4H10) and, most commonly, mixes including both propane and butane, depending on the season — in winter more propane, in summer more butane In the United States, primarily only two grades of LPG are sold, commercial propane and HD-5. The Gas Processors Association (GPA) and the American Society of Testing and Materials (ASTM) publish these specifications. Propane/butane blends are also listed in these specifications. Propylene, butylenes and various other hydrocarbons are usually also present in small concentrations. HD-5 limits the amount of propylene that can be placed in LPG, and is utilized as an autogas specification. A powerful odorant, ethanethiol, is added so that leaks can be detected easily. The international standard is EN 589. In the United States, tetrahydrothiophene (thiophane) or amyl mercaptan are also approved odorants, although neither is currently being utilized.

           

LPG is prepared by refining petroleum or "wet" natural gas, and is almost entirely derived from fossil fuel sources, being manufactured during the refining of petroleum (crude oil), or extracted from petroleum or natural gas streams as they emerge from the ground. Dr. Walter Snelling first produced it in 1910, and the first commercial products appeared in 1912. It currently provides about 3% of all energy consumed, and burns relatively cleanly with no soot and very few sulfur emissions. As it is a gas, it does not pose ground or water pollution hazards, but it can cause air pollution. LPG has a typical specific calorific value of 46.1 MJ/kg compared with 42.5 MJ/kg for fuel oil and 43.5 MJ/kg for premium grade petrol (gasoline). However, its energy density per volume unit of 26 MJ/L is lower than either that of petrol or fuel oil, as its relative density is lower (about 0.5—0.58, compared to 0.71—0.77 for gasoline).

           

In places like the US, Thailand, and India, there are five to ten times more stations thus making the fuel more accessible than NGV stations. Other countries like Poland, South Korea, and Turkey, LPG stations and autos are widespread while NGVs are not. In addition, in some countries such as Thailand, the retail LPG fuel is considerably cheaper in cost.        Though ANG (adsorbed natural gas) has not yet been used in either providing neither stations nor consumer storage tanks, its low compression (500psi vs 3600 psi) has the potential to drive down costs of NGV infrastructure and vehicle tanks.


 
The primary component of natural gas is methane (CH4), the shortest and lightest hydrocarbon molecule. It may also contain heavier gaseous hydrocarbons such as ethane (C2H6), propane (C3H8) and butane (C4H10), as well as other gases, in varying amounts. Hydrogen sulfide (H2S) is a common contaminant, which must be removed prior to most uses. Combustion of one cubic meter yields 38 MJ (10.6 kWh). Natural gas has the highest energy/carbon ratio of any fossil fuel, and thus produces less carbon dioxide per unit of energy.



            The major difficulty in the use of natural gas is transportation. Natural gas pipelines are economical and common on land and across medium-length stretches of water (like Langeled, Interconnector and Trans-Mediterranean Pipeline), but are impractical across large oceans. Liquefied natural gas (LNG) tanker ships, railway tankers, and tank trucks are also used.



            CNG is typically stored in steel or composite containers at high pressure (3000 to 4000 psi, or 205 to 275 bar). These containers are not typically temperature controlled, but are allowed to stay at local ambient temperature. There are many standards for CNG cylinders; the most popular one is ISO 11439. For North America the standard is ANSI NGV-2.

           

LNG storage pressures are typically around 50-150 psi, or 3 to 10 bar. At atmospheric pressure, LNG is at a temperature of -260°F (-162°C), however, in a vehicle tank under pressure the temperature is slightly higher (see saturated fluid). Storage temperatures may vary due to varying composition and storage pressure. LNG is far denser than even the highly compressed state of CNG. As a consequence of the low temperatures, vacuum insulated storage tanks typically made of stainless steel are used to hold LNG.

           

CNG can be stored at lower pressure in a form known as an ANG (Adsorbed Natural Gas) tank at 35 bar (500 psi, the pressure of gas in natural gas pipelines) in various sponge like materials, such as activated carbon and metal-organic frameworks (MOFs). The fuel is stored at similar or greater energy density than CNG. This means that vehicles can be refueled from the natural gas network without extra gas compression; the fuel tanks can be slimmed down and made of lighter, less strong materials.

           

As its boiling point is below room temperature, LPG will evaporate quickly at normal temperatures and pressures and is usually supplied in pressurized steel vessels. They are typically filled to between 80 percent and 85 percent of their capacity to allow for thermal expansion of the contained liquid. The ratio between the volumes of the vaporized gas and the liquefied gas varies depending on composition, pressure, and temperature, but is typically around 250:1. The pressure at which LPG becomes liquid, called its vapor pressure, likewise varies depending on composition and temperature; for example, it is approximately 220 kilopascals (32 psi) for pure butane at 20 °C (68 °F), and approximately 2.2 megapascals (320 psi) for pure propane at 55 °C (131 °F). LPG is heavier than air, unlike natural gas, and thus will flow along floors and tend to settle in low spots, such as basements. There are two main dangers from this. The first is a possible explosion if the mixture of LPG and air is within the explosive limits and there is an ignition source. The second is suffocation due to LPG displacing air, causing a decrease in oxygen concentration. In addition, an odorant is mixed with LPG used for fuel purposes so that leaks can be detected more easily.

           

Conversion kits for gasoline or diesel to LNG/CNG are available in many countries, along with the labor to install them. However, the range of prices and quality of conversion vary enormously. Recently, regulations involving certification of installations in USA has been loosened to include certified private companies, those same kit installations for CNG have fallen to the $6,000+ range (depending on type of vehicle).

           

With the recent increase in natural gas production due to widespread use of fracking technology, many countries, including the United States and Canada, now can be self-sufficient. Canada is a substantial net exporter of natural gas, though the United States still has a net import of natural gas. Natural gas prices have decreased dramatically in the past few years and are likely to decrease further as additional production comes on line. However, the EIA predicts that natural gas prices will start increasing in a few years as the most profitable natural gas reserves are used up. Natural gas prices have decreased from $13 per mmbtu (USD) in 2008 to $3 per mmbtu (USD) in 2012. It is likely therefore that natural gas-powered vehicles will be increasingly cheaper to run relative to gasoline-powered vehicles. The issue is how to finance the purchase and installation of conversion kits. Some support may be available through the Department of Energy. Private initiatives, which essentially lease the conversion equipment in exchange for slightly higher natural gas refueling, can be self-financing and offer considerable advantages to liquidity strapped consumers.

           

Natural Gas has been used as a motor fuel in Canada for over 20 years.http://en.wikipedia.org/wiki/Natural_gas_vehicle - cite_note-36 With assistance from federal and provincial research programs, demonstration projects, and NGV market deployment programs during the 1980s and 1990s, the population of light-duty NGVs grew to over 35,000 by the early 1990s. This assistance resulted in a significant adoption of natural gas transit buses as well. The NGV market started to decline after 1995, eventually reaching today’s vehicle population of about 12,000.



            This figure includes 150 urban transit buses, 45 school buses, 9,450 light-duty cars and trucks, and 2,400 forklifts and ice-resurfacers. The total fuel use in all NGV markets in Canada was 1.9 petajoules (PJs) in 2007 (or 54.6 million litres of gasoline litres equivalent), down from 2.6 PJs in 1997. Public CNG refueling stations have declined in quantity from 134 in 1997 to 72 today. There are 22 in British Columbia, 12 in Alberta, 10 in Saskatchewan, 27 in Ontario, and 1 in Québec. There are only 12 private fleet stations.



            As of December 2009, the U.S. had a fleet of 114,270 compressed natural gas (CNG) vehicles, 147,030 vehicles running on liquefied petroleum gas (LPG), and 3,176 vehicles running on liquefied natural gas (LNG). The NGV fleet is made up mostly of transit buses but there are also some government fleet cars and vans, as well as increasing number of corporate trucks replacing diesel versions, most notably Waste Management, Inc and UPS trucks. As of 12-Dec-2013 Waste Management has a fleet of 2000 CNG Collection trucks; as of 12-Dec-2013 UPS has 2700 alternative fuel vehicles. As of February 2011, there were 873 CNG refueling sites, 2,589 LPG sites, and 40 LNG sites, led by California with 215 CNG refueling stations in operation, 228 LPG sites and 32 LNG sites. The number of refueling stations includes both public and private sites, and not all are available to the public. As of December 2010, the U.S. ranked 6th in the world in terms of number of NGV stations.



            When LPG is used to fuel internal combustion engines, it is often referred to as autogas or auto propane. In some countries, it has been used since the 1940s as a petrol alternative for spark ignition engines. In some countries, there are additives in the liquid that extend engine life and the ratio of butane to propane is kept quite precise in fuel LPG. Two recent studies have examined LPG-fuel-oil fuel mixes and found that smoke emissions and fuel consumption are reduced but hydrocarbon emissions are increased. The studies were split on CO emissions, with one finding significant increases, and the other finding slight increases at low engine load but a considerable decrease at high engine load. Its advantage is that it is non-toxic, non-corrosive and free of tetraethyllead or any additives, and has a high octane rating (102-108 RON depending on local specifications). It burns cleanlier than petrol or fuel oil and is especially free of the particulates from the latter.

           

            LPG has a lower energy density than either petrol or fuel oil, so the equivalent fuel consumption is higher. Many governments impose less tax on LPG than on petrol or fuel oil, which helps offset the greater consumption of LPG than of petrol or fuel oil. However, in many European countries this tax break is often compensated by a much higher annual road tax on cars using LPG than on cars using petrol or fuel oil. Propane is the third most widely used motor fuel in the world. 2008 estimates are that over 13 million vehicles are fueled by propane gas worldwide. Over 20 million tons (over 7 billion US gallons) are used annually as a vehicle fuel.



            Not all automobile engines are suitable for use with LPG as a fuel. LPG provides less upper cylinder lubrication than petrol or diesel, so LPG-fueled engines are more prone to valve wear if they are not suitably modified. Many modern common rail diesel engines respond well to LPG use as a supplementary fuel. This is where LPG is used as fuel as well as diesel. Systems are now available that integrate with OEM engine management systems.



            The recent increases in natural gas production in the United States, now number one in the world in CNG production, makes looking at this technology extremely attractive. Commercial fleets are increasingly looking at conversion to natural gas, with the biggest movement now being explored is in the commercial trucking industry. With tighter regulations on commercial diesel emissions, CNG appears to be the answer being explored the most and expect to see major changes over the next few years. If this conversion is successful, which appears highly likely, heavy truck emissions would be cut significantly.



            Next week we will wrap up the discussion on alternative fuels. Some information for this article obtained from Wikipedia.org.



This week’s recalls:



1,176,407 008-2013 Buick Enclave and GMC Acadia and 2009-2013 Chevrolet Traverse and 2008-2010 Saturn Outlook vehicles.
In the affected vehicles, increased resistance in the driver and passenger seat mounted side impact air bag (SIAB) wiring harnesses may result in the SIAB and seat belt pretensioners not deploying in the event of a crash. Failure of the side impact air bags and seat belt pretensioners to deploy in a crash increases the risk of injury to the driver and front seat occupant.



303,013 009-2014 Chevrolet Express and GMC Savana vans manufactured January 27, 2009, through March 7, 2014.
With a gross vehicle weight rating of 10,000 pounds and less and equipped with front passenger air bags. In the affected vehicles, during a frontal impact below the air bag deployment threshold, if an unbelted front passenger's head hits the instrument panel above where the passenger air bag is located, the panel may not sufficiently absorb the impact. As such, these vehicles fail to meet the requirements of Federal Motor Vehicle Safety Standard number 201, "Occupant Protection in Interior Impact." In the event of a crash below the air bag deployment threshold, an unbelted front passenger seat occupant has an increased risk of injury.



63,903 2013-2014 Cadillac XTS vehicles manufactured February 14, 2012, through March 7, 2014.
In the affected vehicles, a cavity plug on the brake booster pump connector may dislodge allowing corrosion of the brake booster pump relay connector. The corrosion of the brake booster pump relay connector may cause a resistive short and melt the connector, increasing the risk of a fire.



886,815 Honda is recalling certain 2005-2010 Honda Odyssey vehicles manufactured June 23, 2004, through September 4, 2010.
In the affected vehicles, the fuel pump strainer cover may deteriorate allowing fuel to leak out. A fuel leak increases the risk of a fire.



18,092 2014 Fiat 500L vehicles manufactured April 5, 2013, through January 22, 2014.

In certain temperatures, moving the transmission shift lever may have a delayed effect or no effect on selecting a transmission gear. If there is no effect, the vehicle might not shift out of the Park position. If there is a delayed effect, the vehicle may move in an unintended or unexpected direction, increasing the risk of a crash.



18,690 2012-2013 Dodge Durango and Jeep Grand Cherokee vehicles manufactured October 11, 2011, through October 1, 2012.
Under certain braking events, the Ready Alert Braking System (RAB) may result in the driver experiencing a hard brake pedal feel. If the driver experiences a hard brake pedal, the driver may not push the pedal as intended, lengthening the distance needed to stop the vehicle and increasing the risk of a crash.



If you own one of these affected vehicles, contact your dealer or the manufacturer for further instructions.

                                   







Friday, February 14, 2014

Ask Joe Mechanic - Diesel Engines (Part 2)


The first subject of this week’s article is how a diesel engine operates. The diesel internal combustion engine differs from the gasoline powered Otto cycle by using highly compressed hot air to ignite the fuel rather than using a spark plug (compression ignition rather than spark ignition).


In the true diesel engine, only air is initially introduced into the combustion chamber. The air is then compressed with a compression ratio typically between 15:1 and 22:1 resulting in 40-bar (4.0 MPa; 580 psi) pressure compared to 8 to 14 bars (0.80 to 1.4 MPa; 120 to 200 psi) in the petrol engine. This high compression heats the air to 550 °C (1,022 °F). At about the top of the compression stroke, fuel is injected directly into the compressed air in the combustion chamber. This may be into a (typically toroidal) void in the top of the piston or a pre-chamber depending upon the design of the engine. The fuel injector ensures that the fuel is broken down into small droplets, and that the fuel is distributed evenly. The heat of the compressed air vaporizes fuel from the surface of the droplets. The heat from the compressed air in the combustion chamber then ignites the vapor; the droplets continue to vaporize from their surfaces and burn, getting smaller, until all the fuel in the droplets has been burnt. The start of vaporization causes a delay period during ignition and the characteristic diesel knocking sound as the vapor reaches ignition temperature and causes an abrupt increase in pressure above the piston. The rapid expansion of combustion gases then drives the piston downward, supplying power to the crankshaft.

As well as the high level of compression allowing combustion to take place without a separate ignition system, a high compression ratio greatly increases the engine's efficiency. Increasing the compression ratio in a spark-ignition engine where fuel and air are mixed before entry to the cylinder is limited by the need to prevent damaging pre-ignition. Since only air is compressed in a diesel engine, and fuel is not introduced into the cylinder until shortly before top dead centre (TDC), premature detonation is not an issue and compression ratios are much higher.


Diesel's original engine injected fuel with the assistance of compressed air, which atomized the fuel and forced it into the engine through a nozzle (a similar principle to an aerosol spray). The nozzle opening was closed by a pin valve lifted by the camshaft to initiate the fuel injection before top dead centre (TDC). This is called an air-blast injection. Driving the three-stage compressor used some power but the efficiency and net power output was more than any other combustion engine at that time.


Diesel engines in service today raise the fuel to extreme pressures by mechanical pumps and deliver it to the combustion chamber by pressure-activated injectors without compressed air. With direct injected diesels, injectors spray fuel through 4 to 12 small orifices in its nozzle. The early air injection diesels always had a superior combustion without the sharp increase in pressure during combustion. Research is now being performed and patents are being taken out to again use some form of air injection to reduce the nitrogen oxides and pollution, reverting to Diesel's original implementation with its superior combustion and possibly quieter operation. In all major aspects, the modern diesel engine holds true to Rudolf Diesel's original design, that of igniting fuel by compression at an extremely high pressure within the cylinder. With much higher pressures and high technology injectors, present-day diesel engines use the so-called solid injection system applied by Herbert Akroyd Stuart for his hot bulb engine. The indirect injection engine could be considered the latest development of these low speed hot bulb ignition engines.



A vital component of all diesel engines is a mechanical or electronic governor which regulates the idling speed and maximum speed of the engine by controlling the rate of fuel delivery. Unlike Otto-cycle engines, incoming air is not throttled and a diesel engine without a governor cannot have a stable idling speed and can easily overspeed, resulting in its destruction. Mechanically governed fuel injection systems are driven by the engine's gear train. 

These systems use a combination of springs and weights to control fuel delivery relative to both load and speed. Modern electronically controlled diesel engines control fuel delivery by use of an electronic control module (ECM) or electronic control unit (ECU). The ECM/ECU receives an engine speed signal, as well as other operating parameters such as intake manifold pressure and fuel temperature, from a sensor and controls the amount of fuel and start of injection timing through actuators to maximize power and efficiency and minimize emissions. Controlling the timing of the start of injection of fuel into the cylinder is a key to minimizing emissions, and maximizing fuel economy (efficiency), of the engine. The timing is measured in degrees of crank angle of the piston before top dead centre. For example, if the ECM/ECU initiates fuel injection when the piston is 10° before TDC, the start of injection, or timing, is said to be 10° BTDC. Optimal timing will depend on the engine design as well as its speed and load.

Advancing the start of injection (injecting before the piston reaches to its SOI-TDC) results in higher in-cylinder pressure and temperature, and higher efficiency, but also results in increased engine noise due to faster cylinder pressure rise and increased oxides of nitrogen (NOx) formation due to higher combustion temperatures. Delaying start of injection causes incomplete combustion; reduced fuel efficiency and an increase in exhaust smoke, containing a considerable amount of particulate matter and unburned hydrocarbons.

Diesel engines have several advantages over other internal combustion engines:

  • They burn less fuel than a petrol engine performing the same work, due to the engine's higher temperature of combustion and greater expansion ratio. Gasoline engines are typically 30 percent efficient while diesel engines can convert over 45 percent of the fuel energy into mechanical.
  • They have no high voltage electrical ignition system, resulting in high reliability and easy adaptation to damp environments. The absence of coils, spark plug wires, etc., also eliminates a source of radio frequency emissions, which can interfere with navigation and communication equipment, which is especially important in marine and aircraft applications.
  • The life of a diesel engine is generally about twice as long as that of a petrol engine due to the increased strength of parts used. Diesel fuel has better lubrication properties than petrol as well.
  • Diesel fuel is distilled directly from petroleum. Distillation yields some gasoline, but the yield would be inadequate without catalytic reforming, which is a more costly process.
  • Diesel fuel is considered safer than petrol in many applications. Although diesel fuel will burn in open air using a wick, it will not explode and does not release a large amount of flammable vapor. The low vapor pressure of diesel is especially advantageous in marine applications, where the accumulation of explosive fuel-air mixtures is a particular hazard. For the same reason, diesel engines are immune to vapor lock.
  • For any given partial load the fuel efficiency (mass burned per energy produced) of a diesel engine remains nearly constant, as opposed to petrol and turbine engines, which use proportionally more fuel with partial power outputs. They generate less waste heat in cooling and exhaust.
  •  Diesel engines can accept super- or turbo-charging pressure without any natural limit, constrained only by the strength of engine components. This is unlike petrol engines, which inevitably suffer detonation at higher pressure.
  • The carbon monoxide content of the exhaust is minimal; therefore diesel engines are used in underground mines.
  • Biodiesel is an easily synthesized, non-petroleum-based fuel (through transesterification) which can run directly in many diesel engines, while gasoline engines either need adaptation to run synthetic fuels or else use them as an additive to gasoline (e.g., ethanol added to gasohol).


    Many configurations of fuel injection have been used over the course of the twentieth century. Most present-day diesel engines use a mechanical single plunger high-pressure fuel pump driven by the engine crankshaft. For each engine cylinder, the corresponding plunger in the fuel pump measures out the correct amount of fuel and determines the timing of each injection. These engines use injectors that are very precise spring-loaded valves that open and close at a specific fuel pressure. Separate high-pressure fuel lines connect the fuel pump with each cylinder. Fuel volume for each single combustion is controlled by a slanted groove in the plunger, which rotates only a few degrees releasing the pressure, and is controlled by a mechanical governor, consisting of weights rotating at engine speed constrained by springs and a lever. The injectors are held open by the fuel pressure. On high-speed engines the plunger pumps are together in one unit. The length of fuel lines from the pump to each injector is normally the same for each cylinder in order to obtain the same pressure delay.


    A cheaper configuration on high-speed engines with fewer than six cylinders is to use an axial-piston distributor pump, consisting of one rotating pump plunger delivering fuel to a valve and line for each cylinder (functionally analogous to points and distributor cap on an Otto engine). 


    Many modern systems have a single fuel pump which supplies fuel constantly at high pressure with a common rail (single fuel line common) to each injector. Each injector has a solenoid operated by an electronic control unit, resulting in more accurate control of injector opening times that depend on other control conditions, such as engine speed and loading, and providing better engine performance and fuel economy.


    Both mechanical and electronic injection systems can be used in either direct or indirect injection configurations. Two-stroke diesel engines with mechanical injection pumps can be inadvertently run in reverse, albeit in a very inefficient manner, possibly damaging the engine. Large ship two-stroke d
    iesels are designed to run in either direction, obviating the need for a gearbox.


    An indirect injection diesel engine delivers fuel into a chamber off the combustion chamber, called a pre-chamber or ante-chamber, where combustion begins and then spreads into the main combustion chamber, assisted by turbulence created in the chamber. This system allows for a smoother, quieter running engine, and because combustion is assisted by turbulence, injector pressures can be lower, about 100 bar (10 MPa; 1,500 psi), using a single orifice tapered jet injector. Mechanical injection systems allowed high-speed running suitable for road vehicles (typically up to speeds of around 4000 rpm. The pre-chamber had the disadvantage of increasing heat loss to the engine's cooling system, and restricting the combustion burn, which reduced the efficiency by five to ten percent. Indirect injection engines are cheaper to build and it is easier to produce smooth, quiet-running vehicles with a simple mechanical system. In road-going vehicles most prefer the greater efficiency and better-controlled emission levels of direct injection. Indirect injection diesels can still be found in the many ATV diesel applications.


    Direct injection diesel engines have injectors mounted at the top of the combustion chamber. The injectors are activated using one of two methods - hydraulic pressure from the fuel pump, or an electronic signal from an engine controller.


    Hydraulic pressure activated injectors can produce harsh engine noise. Fuel consumption is about 15 to 20 percent lower than indirect injection diesels. The extra noise is generally not a problem for industrial uses of the engine, but for automotive usage, buyers have to decide whether or n
    ot the increased fuel efficiency would compensate for the extra noise.

    Electronic control of the fuel injection transformed the direct injection engine by allowing much greater control over the combustion.


     Unit direct injection also injects fuel directly into the cylinder of the engine. In this system the injector and the pump are combined into one unit positioned over each cylinder controlled by the camshaft. Each cylinder has its own unit eliminating the high-pressure fuel lines, achieving a more consistent injection. Volkswagen AG uses this type of injection system, also developed by Bosch, in cars (where it is called a Pumpe-Düse-System—literally pump-nozzle system) and by Mercedes Benz ("PLD") and most major diesel engine manufacturers in large commercial engines (CAT, Cummins, Detroit Diesel, Electro-Motive Diesel, Volvo). With recent advancements, the pump pressure has been raised to 2,400 bars (240 MPa; 35,000 psi), allowing injection parameters similar to common rail systems.


     In common rail systems, the separate pulsing high-pressure fuel line to each cylinder's injector is also eliminated. Instead, a high-pressure pump pressurizes fuel at up to 2,500 bar (250 MPa; 36,000 psi), in a "common rail". The common rail is a tube that supplies each computer-controlled injector containing a precision-machined nozzle and a plunger driven by a solenoid or piezoelectric actuator.


    In cold weather, high-speed diesel engines can be difficult to start because the mass of the cylinder block and cylinder head absorb the heat of compression, preventing ignition due to the higher surface-to-volume ratio. Pre-chambered engines make use of small electric heaters inside the pre-chambers called glowplugs, while the direct-injected engines have these glowplugs in the combustion chamber.


    Many engines use resistive heaters in the intake manifold to warm the inlet air for starting, or until the engine reaches operating temperature. Engine block heaters (electric resistive heaters in the engine block) connected to the utility grid are used in cold climates when an engine is turned off for extended periods (more than an hour), to reduce startup time and engine wear. Block heaters are also used for emergency power standby Diesel-powered generators, which must rapidly pick up load on a power failure. In the past, a wider variety of cold-start methods were used. Some engines, such as Detroit Diesel engines used a system to introduce small amounts of ether into the inlet manifold to start combustion. Others used a mixed system, with a resistive heater-burning methanol. An impromptu method, particularly on out-of-tune engines, is to manually spray an aerosol can of ether-based engine starter fluid into the intake air stream (usually through the intake air filter assembly).


    Diesel fuel is also prone to waxing or gelling in cold weather; both are terms for the solidification of diesel oil into a partially crystalline state. The crystals build up in the fuel line (especially in fuel filters), eventually starving the engine of fuel and causing it to stop running. Low-output electric heaters in fuel tanks and around fuel lines are used to solve this problem. Also, most engines have a spill return system, by which any excess fuel from the injector pump and injectors is returned to the fuel tank. Once the engine has warmed, returning warm fuel prevents waxing in the tank.


    Due to improvements in fuel technology with additives, waxing rarely occurs in all but the coldest weather when a mix of diesel and kerosene may be used to run a vehicle. Gas stations in regions with a cold climate are required to offer winterized diesel in the cold seasons that allow operation below a specific Cold Filter Plugging Point. In Europe these diesel characteristics are described in the EN 590 standard.


    Most diesels are now turbocharged and some are both turbocharged and supercharged. Because diesels do not have fuel in the cylinder before combustion is initiated, more than one bar (100 kPa) of air can be loaded in the cylinder without pre-ignition. A turbocharged engine can produce significantly more power than a naturally aspirated engine of the same configuration, as having more air in the cylinders allows more fuel to be burned and thus more power to be produced. A supercharger is powered mechanically by the engine's crankshaft, while the engine exhaust, not requiring any mechanical power, powers a turbocharger. Turbocharging can improve the fuel economy of diesel engines by recovering waste heat from the exhaust, increasing the excess air factor, and increasing the ratio of engine output to friction losses.


    A two-stroke engine does not have a discrete exhaust and intake stroke and thus is incapable of self-aspiration. Therefore all two-stroke engines must be fitted with a blower to charge the cylinders with air and assist in dispersing exhaust gases, a process referred to as scavenging. In some cases, the engine may also be fitted with a turbocharger, whose output is directed into the blower inlet. A few designs employ a hybrid turbocharger for scavenging and charging the cylinders, which device is mechanically driven at cranking and low speeds to act as a blower.


    As turbocharged or supercharged engines produce more power for a given engine size as compared to naturally aspirated engines, attention must be paid to the mechanical design of components, lubrication, and cooling to handle the power. Pistons are usually cooled with lubrication oil sprayed on the bottom of the piston. Large engines may use water, seawater, or oil supplied through telescoping pipes attached to the crosshead.


    As with petrol engines, there are two classes of diesel engines in current use: two-stroke and four-stroke. The four-stroke type is the "classic" version, tracing its lineage back to Rudolf Diesel's prototype. It is also the most commonly used form, being the preferred power source for many motor vehicles, especially buses and trucks. Much larger engines, such as used for railroad locomotion and marine propulsion, are often two-stroke units, offering a more favorable power-to-weight ratio, as well as better fuel economy


    Two-stroke diesel engine operation is similar to that of petrol counterparts, except that fuel is not mixed with air before induction, and the crankcase does not take an active role in the cycle. The traditional two-stroke design relies upon a mechanically driven positive displacement blower to charge the cylinders with air before compression and ignition. The charging process also assists in expelling (scavenging) combustion gases remaining from the previous power stroke.


    The archetype of the modern form of the two-stroke diesel is the (high-speed) Detroit Diesel Series 71 engine, designed by Charles F. "Boss" Kettering and his colleagues at General Motors Corporation in 1938, in which the blower pressurizes a chamber in the engine block that is often referred to as the "air box". The (very much larger medium-speed) Electro-Motive Diesel engine is used as the prime mover in EMD diesel-electric locomotive, marine and stationary applications, and was designed by the same team, and is built to the same principle. However, a significant improvement built into later EMD engines is the mechanically assisted turbo-compressor, which provides charge air using mechanical assistance during starting (thereby obviating the necessity for Roots-blown scavenging), and provides charge air using an exhaust gas-driven turbine during normal operations—thereby providing true turbocharging and additionally increasing the engine's power output by at least fifty percent. 


    In a two-stroke diesel engine, as the cylinder's piston approaches the bottom dead centre exhaust ports or valves are opened relieving most of the excess pressure after which a passage between the air box and the cylinder is opened, permitting air flow into the cylinder. The airflow blows the remaining combustion gases from the cylinder—this is the scavenging process. As the piston passes through bottom center and starts upward, the passage is closed and compression commences, culminating in fuel injection and ignition. Refer to two-stroke diesel engines for more detailed coverage of aspiration types and supercharging of two-stroke diesel engines.


    Normally, the number of cylinders is used in multiples of two, although any number of cylinders can be used as long as the load on the crankshaft is counterbalanced to prevent excessive vibration. The inline-six-cylinder design is the most prolific in light- to medium-duty engines, though small V8 and larger inline-four displacement engines are also common. Small-capacity engines (generally considered to be those below five liters in capacity) are generally four- or six-cylinder types, with the four-cylinder being the most common type found in automotive uses. Five-cylinder diesel engines have also been produced, being a compromise between the smooth running of the six-cylinder and the space-efficient dimensions of the four-cylinder. Diesel engines for smaller plant machinery; boats, tractors, generators and pumps may be four-, three- or two-cylinder types, with the single-cylinder diesel engine remaining for light stationary work. Direct reversible two-stroke marine diesels need at least three cylinders for reliable restarting forwards and reverse, while four-stroke diesels need at least six cylinders.


    The desire to improve the diesel engine's power-to-weight ratio produced several novel cylinder arrangements to extract more power from a given capacity. The uniflow opposed-piston engine uses two pistons in one cylinder with the combustion cavity in the middle and gas in- and outlets at the ends. This makes a comparatively light, powerful, swiftly running and economic engine suitable for use in aviation. An example is the Junkers Jumo 204/205. The Napier Deltic engine, with three cylinders arranged in a triangular formation, each containing two opposed pistons, the whole engine having three crankshafts, is one of the better known.


    Some information for this article obtained from Wikipedia.org.


    Recent Recalls:

    27,933 Ford 2012-2013 Edge vehicles equipped with 2.0L engines.
    The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized. A fuel leak in the presence of an ignition source may result in a fire.


    300 Ford 2011-2012 Explorers certain replacement steering gears installed as service parts.
    The affected gears may lock, preventing the driver from being able to steer the vehicle. The inability to steer the vehicle increases the risk of a crash.


    Contact your local dealership for more information and how to proceed.







Thursday, December 19, 2013

Ask Joe Mechanic: Alternative Energy Vehicles - Part 3A


This week and next week we will point out some of the positive and negative facts about hybrid vehicles including fuel efficiency, emissions reductions, environmental impacts of the hybrid battery, costs and availability of raw materials, and pedestrian safety concerns.

The first two items, fuel efficiency and emissions reductions go hand-in-hand, so we will discuss them together.  The hybrid vehicle typically achieves greater fuel economy and lower emissions than conventional internal combustion engine vehicles (ICEVs), resulting in fewer emissions being generated. These savings are primarily achieved by three elements of a typical hybrid design:
  1. Relying on both the engine and the electric motors for peak power needs, resulting in a smaller engine, sized more for average usage rather than peak power usage. A smaller engine can have less internal losses and lower weight.
  2. Having significant battery storage capacity to store and reuse recaptured energy, especially in stop-and-go traffic typical of the city driving cycle.
  3. Recapturing significant amounts of energy during braking that are normally wasted as heat. This regenerative braking reduces vehicle speed by converting some of its kinetic energy into electricity, depending upon the power rating of the motor/generator.

Other techniques that are not necessarily a ‘hybrid’ feature, but that are frequently found on hybrid vehicles include:
  1. Using Atkinson cycle engines (reverse rotation) instead of Otto cycle engines for improved fuel economy.
  2. Shutting down the engine during traffic stops or while coasting or during other idle periods.
  3. Improving aerodynamics: (part of the reason that SUVs get such bad fuel economy is the drag on the car. A box-shaped car or truck has to exert more force to move through the air causing more stress on the engine making it work harder). Improving the shape and aerodynamics of a car is a good way to help better the fuel economy and also improve handling at the same time.
  4. Using low rolling resistance tires (tires were often made to give a quiet, smooth ride, high grip, etc., but efficiency was a lower priority). Tires cause mechanical drag, once again making the engine work harder, consuming more fuel. Hybrid cars may use special tires that are more inflated than regular tires and stiffer or by choice of carcass structure and rubber compound, have lower rolling resistance while retaining acceptable grip, and so improving fuel economy whatever the power source.
  5. Powering the air conditioning, power steering, and other auxiliary pumps electrically as and when needed. This reduces mechanical losses when compared with driving them continuously with traditional engine belts.

    These features make a hybrid vehicle particularly efficient for city traffic where there are frequent stops, coasting and idling periods. In addition, noise emissions are reduced, particularly at idling and low operating speeds, in comparison to conventional engine vehicles. For continuous high-speed highway use these features are much less useful in reducing emissions.
     

Hybrid vehicle emissions today are getting close to or even lower than the recommended level set by the Environmental Protection Agency (EPA). The recommended levels they suggest for a typical passenger vehicle should equate to 5.5 metric tons of carbon dioxide. The three most popular hybrid vehicles, Honda Civic, Honda Insight and Toyota Prius, set the standards even higher by producing 4.1, 3.5, and 3.5 tons showing a major improvement in carbon dioxide emissions. Hybrid vehicles can reduce air emissions of smog-forming pollutants by up to 90% and cut carbon dioxide emissions in half.


As regarding the environmental impacts of the hybrid battery, the industry is still in the learning stage. What has not totally been developed yet is the full technology for recycling of spent hybrid batteries because of their relative newness. While we do know that they are more environmentally friendly than the conventional lead-acid vehicle battery, that battery has a well-established recycling process in place for many years.  The conventional battery has its problems with controlling lead emissions. Today most hybrid car batteries are either nickel metal hydride or lithium ion. Of the two, the lithium ion has the lower toxicity.

We will continue this battery discussion and more in next week’s column.

Recent recalls:

374 2013 Dodge Dart
Vehicles equipped with the Mopar 13 trim package. In the affected vehicles, the front seat mounted side airbags (SAB) may not have been properly installed into the seat. In the event of a crash necessitating SAB deployment, the SABs may fail to deploy as intended, increasing the risk of injury.


2,608 2007-2009 BMW F 800 S and F 800 ST motorcycles

Due to incorrect tolerances, the rear wheel drive bearing and rear axle may wear. Bearing and axle wear may affect handling and control of the motorcycle, increasing the risk of a crash.

130 Mercedes-Benz 2013 SL63, SL550, and SL65

The affected vehicles are equipped with an occupant classification system (OCS) that may not detect a very light person sitting in the front passenger seat. If the OCS does not detect a very light person sitting in the seat, the passenger side air bag would be turned off.  In the event of a crash necessitating side air bag deployment, the passenger would be at an increased risk of injury.


2,475 BMW 2012 K1600 GT and K1600 GTL motorcycles

In certain riding conditions, an incorrect throttle valve control signal may be received by the engine control unit, limiting the engine speed. As a result of the reduced engine speed, the engine could stall, increasing the risk of a crash.


22,483 Harley-Davidson 2014 FLHTCUTG, FXSBE, and FLSTNSE FLHTCU, FLHTK, FLHTP, FLHX, FLHXS, FLHTKSE, and FLHRSE motorcycles

The affected motorcycles may have been built with an incorrect clutch release plate. Additionally, The clutch master cylinder may allow air into the clutch system. Either condition may prevent the clutch from disengaging. If the clutch does not disengage, the rider may have difficulty slowing or stopping the motorcycle, increasing the risk of a crash.


If you own one of these vehicles, contact your local dealer for further instructions on how to proceed.